INDEX
23XL Machine Familiarization, 4
Abbreviations and Explanations, 4
Adding Refrigerant, 63
Adjusting the Refrigerant Charge, 63
After Extended Shutdown, 58
After Limited Shutdown, 58
Attach To Network Device Control, 35
Automatic Soft Stop Amps Threshold, 38
Auto.-Restart After Power Failure, 31
Before Initial Start-Up, 39
Calibrate Motor Current Demand Setting, 57
Capacity Overrides, 29
Carrier Comfort Network Interface, 49
Changing Oil and Oil Filter, 64
Charge Refrigerant Into Machine, 55
Chilled Water Recycle Mode, 38
Cold Weather Operation, 59
Compressor Bearing Maintenance, 66
Compressor Rotor Check, 66
Condenser, 7
Condenser Freeze Prevention, 31
Condenser Pump Control, 29
Control Algorithm Checkout Procedure, 69
Control Center, 7, 64
Control Modules, 80
Controls, 13
Controls Definitions, 13
Control Test, 69
Cooler, 7
Demand Limit Control, Option, 32
Design Set Points (Input), 52
Details (Lubrication Cycle), 7
Display Messages (Check), 68
Dry Run to Test Start-Up Sequence, 56
Extended Shutdown, 58
Factory-Mounted Starter, 7
Field Supplied Equipment Required, 39
General Controls Overview, 13
General Maintenance, 63
Heat Exchanger Tubes (Inspect), 66
High Altitude Locations, 52
Hot Gas Bypass Algorithm, 32
Ice Build Control, 34
Initial Start-Up, 56
Instruct the Operator, 57
Introduction, 4
Job Data Required, 39
Lead/Lag Control, 33
Leak Test Machine, 40
LID Operation and Menus, 17
Local Occupied Schedule (Input), 52
Local Start-Up, 37
Lubrication Cycle, 7
Lubrication System (Check), 64
Machine Dehydration, 48
Machine Identification Nameplate, 4
Machine Operating Conditions (Check), 57
Machine Tightness (Check), 39
Machines with Isolation Valves, 62
Machines with Storage Tanks, 61
Motor Cooling Cycle, 7
Motor-Compressor, 7
Muffler-Oil Separator, 7
Notes on Module Operation, 80
Oil Charge, 50
Oil Loss Prevention, 8
Oil Pressure and Compressor Stop (Check), 57
Oil Reclaim System, 8
Oil Separator Coalescer, 66
Oil Specification, 66
Oil Sump Temperature Control, 29
Open Oil Circuit Valves, 39
Operating Instructions, 58
Operating the Optional Pumpout Compressor, 61
Operator Duties, 58
Optional Pumpout Compressor Water Piping (Check), 48
Optional Pumpout System Controls and
Compressor (Check), 55
Optional Pumpout System Maintenance, 67
Options Modules (8-Input), 81
Ordering Replacement Chiller Parts, 68
Overview (Troubleshooting Guide), 68
Physical Data, 89
PIC System Components, 13
PIC System Functions, 22
Power Up the Controls and Check the Oil Heater, 50
Preparation (for Initial Start-Up), 56
Preparation (for Pumpout and Refrigeration
Transfer Procedures), 61
Prepare the Machine for Start-Up, 58
Pressure Transducers (Check), 67, 68
Processor Module (PSIO), 81
Pumpout and Refrigerant Transfer Procedures, 61
Ramp Loading Control, 29
Refrigerant Charge (Trim), 64
Refrigerant Filter/Drier, 66
Refrigerant Float System (Inspect), 66
Refrigerant Leak Testing, 63
Refrigerant Leak Rate, 64
Refrigerant Properties, 63
Refrigerant Strainers, 66
Refrigerant Tracer, 39
Refrigeration Cycle, 7
Refrigeration Log, 59
Relief Devices (Check), 48
Relief Valves and Piping (Inspect), 66
Remote Start/Stop Controls, 29
Remove Shipping Packaging, 39
Removing Refrigerant, 63
Repair Refrigerant Leak, Retest, and Apply Standing
Vacuum Test, 64
Replacing Defective Processor Modules, 82
Return Refrigerant to Normal Operating Conditions, 63
Rotation (Check), 56
Running System (Check), 58
Safety and Operating Controls (Check), 64
Safety Considerations, 1
Safety Controls, 23
Safety Shutdown, 39
Scheduled Maintenance, 64
Service Configurations, 53
Service Ontime, 64
Service Operation, 36
Selecting Refrigerant Type, 53
Set Up Machine Control Configuration, 50
Shutdown Sequence, 38
Slide Valve Operation, 59
Slide Valve Principle, 11
Solid-State Starters, 83
Spare Safety Inputs, 29
Standing Vacuum Test, 48
Starter (Check), 49
Starter Management Module (SMM), 81
Starting Equipment, 11, 67
Start-Up/Shutdown/Recycle Sequence, 37
Storage Vessel, 7
System Components, 4
Summary (Lubrication Cycle), 7
Temperature Sensors (Check), 68
Test After Service, Repair, or Major Leak, 64
To Prevent Accidental Start-Up, 57
To Start the Machine, 58
103
Komentarze do niniejszej Instrukcji