Carrier 48DL Instrukcja Instalacji

Przeglądaj online lub pobierz Instrukcja Instalacji dla Pompy ciepła Carrier 48DL. Carrier 48DL Installation manual Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
Przeglądanie stron 0
INSTALLATION
MANUAL
CAUTION: READ ALL SAFETY GUIDES BEFORE YOU
BEGIN TO INSTALL YOUR UNIT.
SAVE THIS MANUAL
264975-BIM-B-1208
CONTENTS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . 5
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
RENEWAL PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
APPROVALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
NOMENCLATURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
START-UP (COOLING) . . . . . . . . . . . . . . . . . . . . . . . . . 66
START-UP (GAS HEAT) . . . . . . . . . . . . . . . . . . . . . . . . 67
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . 74
See following pages for a complete Table of Contents.
NOTES, CAUTIONS AND WARNINGS
The installer should pay particular attention to the words:
NOTE, CAUTION, and WARNING. Notes are intended to
clarify or make the installation easier. Cautions
are given
to prevent equipment damage. Warnings
are given to alert
installer that personal injury and/or equipment damage
may result if installation procedure is not handled properly.
Tested in accordance with:
SINGLE PACKAGE AIR CONDITIONERS AND
SINGLE PACKAGE GAS/ELECTRIC UNITS
DL/DU -06, -07, -08, -10 and -12
6-1/2 TO 12-1/2 TON
(9.0 TO 11.5 EER)
Przeglądanie stron 0
1 2 3 4 5 6 ... 83 84

Podsumowanie treści

Strona 1 - INSTALLATION

INSTALLATION MANUALCAUTION: READ ALL SAFETY GUIDES BEFORE YOU BEGIN TO INSTALL YOUR UNIT.SAVE THIS MANUAL264975-BIM-B-1208 CONTENTSGENERAL . . . . . .

Strona 2 - TABLE OF CONTENTS

264975-BIM-B-120810 Johnson Controls Unitary Products LOCATIONUse the following guidelines to select a suitable location forthese units:1. Unit is des

Strona 3 - LIST OF TABLES

264975-BIM-B-1208Johnson Controls Unitary Products 116. Maintain level tolerance to 1/2” across the entire width and length of unit.RIGGING AND HANDLI

Strona 4 - LIST OF TABLES (CONT’D)

264975-BIM-B-120812 Johnson Controls Unitary Products FIGURE 7 - UNIT CENTER OF GRAVITYCLEARANCESAll units require particular clearances for proper o

Strona 5 - INSPECTION

264975-BIM-B-1208Johnson Controls Unitary Products 13NOTE: A one-inch clearance must be provided betweenany combustible material and the supply ductwo

Strona 6 - APPROVALS

264975-BIM-B-120814 Johnson Controls Unitary Products.FIGURE 9 - BOTTOM DUCT OPENINGS (FROM ABOVE)ReturnAirSupplyAir32-11/166-13/166-13/166-13/1621-3

Strona 7 - NOMENCLATURE

264975-BIM-B-1208Johnson Controls Unitary Products 15DUCTWORKDuctwork should be designed and sized according to themethods in Manual D of the Air Cond

Strona 8

264975-BIM-B-120816 Johnson Controls Unitary ProductsNote orientation. Panel is “insulation” side up.CONDENSATE DRAINThe side condensate drain is reve

Strona 9 - LIMITATIONS

264975-BIM-B-1208Johnson Controls Unitary Products 17THERMOSTAT WIRINGThe thermostat should be located on an inside wall approxi-mately 56 inch above

Strona 10 - LOCATION

264975-BIM-B-120818 Johnson Controls Unitary ProductsFIGURE 17 - TYPICAL ELECTRONIC THERMOSTAT FIELD WIRINGW 2R CR HY 1Y 2W 1GCX 1X 3X 4A 1A 2TTW 2Y

Strona 11 - TABLE 4: 4 POINT LOAD WEIGHT

264975-BIM-B-1208Johnson Controls Unitary Products 19FIGURE 19 - FIELD WIRING DISCONNECT - COOLING UNIT WITH/WITHOUT ELECTRIC HEATTERMINAL BLOCK TB1F

Strona 12 - FIGURE 6 - UNIT 6 POINT LOAD

264975-BIM-B-12082 Johnson Controls Unitary ProductsTABLE OF CONTENTSGENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Strona 13 - See Detail

264975-BIM-B-120820 Johnson Controls Unitary ProductsTABLE 9: ELECTRICAL DATA - DL-06 (6-1/2 TON) STANDARD EFFICIENCY W/O PWRD CONV. OUTLETTABLE 10: E

Strona 14 - 42” 27 3/4 12 1/16 27 1/2

264975-BIM-B-1208Johnson Controls Unitary Products 21TABLE 11: ELECTRICAL DATA - DU-06 (6-1/2 TON) HIGH EFFICIENCY W/O PWRD CONV. OUTLETTABLE 12: ELEC

Strona 15 - DUCT COVERS

264975-BIM-B-120822 Johnson Controls Unitary ProductsTABLE 13: ELECTRICAL DATA - DL-07 (7-1/2 TON) STANDARD EFFICIENCY W/O PWRD CONV. OUTLETTABLE 14:

Strona 16 - 3 " M i n i m u m

264975-BIM-B-1208Johnson Controls Unitary Products 23TABLE 15: ELECTRICAL DATA - DU-07 (7-1/2 TON) HIGH EFFICIENCY W/O PWRD CONV. OUTLETTABLE 16: ELEC

Strona 17 - TABLE 8: CONTROL WIRE SIZES

264975-BIM-B-120824 Johnson Controls Unitary ProductsTABLE 17: ELECTRICAL DATA - DL-08 (8-1/2 TON) STANDARD EFFICIENCY W/O PWRD CONV. OUTLETTABLE 18:

Strona 18 - B O A R D

264975-BIM-B-1208Johnson Controls Unitary Products 25TABLE 19: ELECTRICAL DATA - DU-08 (8-1/2 TON) HIGH EFFICIENCY W/O PWRD CONV. OUTLETTABLE 20: ELEC

Strona 19 - 264975-BIM-B-1208

264975-BIM-B-120826 Johnson Controls Unitary ProductsTABLE 21: ELECTRICAL DATA - DL-10 (10 TON) STANDARD EFFICIENCY W/O PWRD CONV. OUTLETTABLE 22: ELE

Strona 20

264975-BIM-B-1208Johnson Controls Unitary Products 27TABLE 23: ELECTRICAL DATA - DU-10 (10 TON) HIGH EFFICIENCY W/O PWRD CONV. OUTLETTABLE 24: ELECTRI

Strona 21

264975-BIM-B-120828 Johnson Controls Unitary ProductsTABLE 25: ELECTRICAL DATA - DL-12 (12-1/2 TON) STANDARD EFFICIENCY W/O PWRD CONV. OUTLETTABLE 26:

Strona 22

264975-BIM-B-1208Johnson Controls Unitary Products 29TABLE 27: ELECTRICAL DATA - DU-12 (12-1/2 TON) HIGH EFFICIENCY W/O PWRD CONV. OUTLETTABLE 28: ELE

Strona 23

264975-BIM-B-1208Johnson Controls Unitary Products 3LIST OF FIGURESFig. # Pg. #1 UNIT SHIPPING BRACKET . . . . . . . . . . . . . . . . . . . . . 82 CO

Strona 24

264975-BIM-B-120830 Johnson Controls Unitary ProductsTABLE 29: DL PHYSICAL DATAComponentModels-06 -07 -08 -10 -12EvaporatorBlowerBlower, Centrifugal (

Strona 25

264975-BIM-B-1208Johnson Controls Unitary Products 31OPTIONAL ELECTRIC HEATThe factory-installed heaters are wired for single point powersupply. Power

Strona 26

264975-BIM-B-120832 Johnson Controls Unitary ProductsNOTE: Maximum capacity of pipe in cubic feet of gas perhour based upon a pressure drop of 0.3 inc

Strona 27

264975-BIM-B-1208Johnson Controls Unitary Products 33LP UNITS, TANKS AND PIPINGAll gas heat units are shipped from the factory equipped fornatural gas

Strona 28

264975-BIM-B-120834 Johnson Controls Unitary ProductsRAIN HOODAll of the hood components, including the filters, the gasket-ing and the hardware for a

Strona 29

264975-BIM-B-1208Johnson Controls Unitary Products 35FIGURE 23 - ENTHALPY SET POINT CHART40(4)70(21)50(10)55(13)60(16)65(18)35(2)45(7)75(24)80(27)35(

Strona 30 - TABLE 30: DU PHYSICAL DATA

264975-BIM-B-120836 Johnson Controls Unitary ProductsPHASINGDL/DU units are properly phased at the factory. Check forproper compressor rotation. If th

Strona 31 - S H O W N

264975-BIM-B-1208Johnson Controls Unitary Products 37TABLE 35: DL-06 (6-1/2 TON) STANDARD MOTOR DOWN SHOT BLOWER PERFORMANCE1 2ESP3TURNS OPEN4012345CF

Strona 32

264975-BIM-B-120838 Johnson Controls Unitary ProductsTABLE 37: DU-06 (6-1/2 TON) STANDARD MOTOR DOWN SHOT BLOWER PERFORMANCE1,2CFM RPMW5BHP CFM RPMW5B

Strona 33 - FIRE OR EXPLOSION HAZARD

264975-BIM-B-1208Johnson Controls Unitary Products 39TABLE 38: DU-06 (6-1/2 TON) OPTIONAL MOTOR DOWN SHOT BLOWER PERFORMANCE1,2CFM RPMW5BHP CFM RPMW5B

Strona 34 - ADJUSTMENTS AND INFORMATION

264975-BIM-B-12084 Johnson Controls Unitary ProductsLIST OF TABLES (CONT’D)Tbl. # Pg. #30 DU PHYSICAL DATA . . . . . . . . . . . . . . . . . . . . . .

Strona 35

264975-BIM-B-120840 Johnson Controls Unitary ProductsTABLE 39: DL, DU-07 (7-1/2 TON) STANDARD MOTOR DOWN SHOT BLOWER PERFORMANCECFM RPMW5BHP CFM RPMW5

Strona 36 - FIGURE 25 - BELT ADJUSTMENT

264975-BIM-B-1208Johnson Controls Unitary Products 41TABLE 40: DL, DU-07 (7-1/2 TON) OPTIONAL MOTOR DOWNSHOT BLOWER PERFORMANCECFM RPMW5BHP CFM RPMW5B

Strona 37

264975-BIM-B-120842 Johnson Controls Unitary ProductsTABLE 41: DL, DU-08 (8-1/2 TON) STANDARD MOTOR DOWN SHOT BLOWER PERFORMANCECFM RPMW5BHP CFM RPMW5

Strona 38

264975-BIM-B-1208Johnson Controls Unitary Products 43TABLE 42: DL, DU-08 (8-1/2 TON) OPTIONAL DRIVE DOWN SHOT BLOWER PERFORMANCECFM RPMW5BHP CFM RPMW5

Strona 39

264975-BIM-B-120844 Johnson Controls Unitary ProductsTABLE 43: DL, DU-10 (10 TON) STANDARD MOTOR DOWN SHOT BLOWER PERFORMANCE1 2ESP3TURNS OPEN4012345C

Strona 40

264975-BIM-B-1208Johnson Controls Unitary Products 45TABLE 45: DL, DU-12 (12-1/2 TON) STANDARD MOTOR DOWN SHOT BLOWER PERFORMANCE1 2ESP3TURNS OPEN4012

Strona 41

264975-BIM-B-120846 Johnson Controls Unitary ProductsTABLE 47: DL-06 (6-1/2 TON) STANDARD MOTOR SIDE SHOT BLOWER PERFORMANCE1 2ESP3TURNS OPEN401 2 345

Strona 42

264975-BIM-B-1208Johnson Controls Unitary Products 47TABLE 49: DU-06 (6-1/2 TON) STANDARD MOTOR SIDE SHOT BLOWER PERFORMANCECFM RPMW5BHP CFM RPMW5BHP

Strona 43

264975-BIM-B-120848 Johnson Controls Unitary ProductsTABLE 50: DU-06 (6-1/2 TON) OPTIONAL MOTOR SIDE SHOT BLOWER PERFORMANCE&)0 530:%+3 &)0 5

Strona 44

264975-BIM-B-1208Johnson Controls Unitary Products 49TABLE 51: DL, DU-07 (7-1/2 TON) STANDARD MOTOR SIDE SHOT BLOWER PERFORMANCECFM RPMW5BHP CFM RPMW5

Strona 45

264975-BIM-B-1208Johnson Controls Unitary Products 5GENERALDL/DU units are single package air conditioners with optionalgas heating designed for outdo

Strona 46

264975-BIM-B-120850 Johnson Controls Unitary ProductsTABLE 52: DL, DU-07 (7-1/2 TON) OPTIONAL SIDE SHOT BLOWER PERFORMANCECFM RPMW5BHP CFM RPMW5BHP CF

Strona 47

264975-BIM-B-1208Johnson Controls Unitary Products 51TABLE 53: DL, DU-08 (8-1/2 TON) STANDARD MOTOR SIDE SHOT BLOWER PERFORMANCECFM RPMW5BHP CFM RPMW5

Strona 48

264975-BIM-B-120852 Johnson Controls Unitary ProductsTABLE 54: DL, DU-08 (8-1/2 TON) OPTIONAL DRIVE SIDE SHOT BLOWER PERFORMANCECFM RPMW5BHP CFM RPMW5

Strona 49

264975-BIM-B-1208Johnson Controls Unitary Products 53TABLE 55: DL, DU-10 (10 TON) STANDARD MOTOR SIDE SHOT BLOWER PERFORMANCE1 2ESP3TURNS OPEN4012345C

Strona 50

264975-BIM-B-120854 Johnson Controls Unitary ProductsTABLE 57: DL, DU-12 (12-1/2 TON) STANDARD MOTOR SIDE SHOT BLOWER PERFORMANCE1 2ESP3TURNS OPEN4012

Strona 51

264975-BIM-B-1208Johnson Controls Unitary Products 55NOTES FOR TABLE 35 THROUGH TABLE 58: • Blower performance includes dry coil and two-inchfilters.•

Strona 52

264975-BIM-B-120856 Johnson Controls Unitary ProductsAIR BALANCEStart the supply air blower motor. Adjust the resistances in both the supply and the r

Strona 53

264975-BIM-B-1208Johnson Controls Unitary Products 57CHECKING AIR QUANTITYMETHOD ONE1. Remove the dot plugs from the duct panel (for location of the d

Strona 54

264975-BIM-B-120858 Johnson Controls Unitary ProductsFIGURE 26 - DRY COIL DELTA P 50" CABINETDL/DU 50" CabinetIndoor Coil Pressure Drop vs.

Strona 55

264975-BIM-B-1208Johnson Controls Unitary Products 59SUPPLY AIR DRIVE ADJUSTMENTAt unit start-up, the measured CFM may be higher or lowerthan the requ

Strona 56 - AIR BALANCE

264975-BIM-B-12086 Johnson Controls Unitary ProductsREFERENCEAdditional information is available in the following referenceforms:• Technical Guide - D

Strona 57 - CHECKING AIR QUANTITY

264975-BIM-B-120860 Johnson Controls Unitary ProductsTABLE 61: ADDITIONAL STATIC RESISTANCE DL-06, -10, -12 AND DU-10, -12CFMCooling Only1Economizer2

Strona 58

264975-BIM-B-1208Johnson Controls Unitary Products 61OPERATIONSEQUENCE OF OPERATIONS OVERVIEWFor the DL/DU series of units, the thermostat makes a cir

Strona 59 - SUPPLY AIR DRIVE ADJUSTMENT

264975-BIM-B-120862 Johnson Controls Unitary Productscompleted. Upon the final compressor de-energizing, theblower is stopped following the elapse of

Strona 60

264975-BIM-B-1208Johnson Controls Unitary Products 63condenser motor failure, (opens at 405 ± 10 psig or 440 ± 10 psig depending on unit model).3. A l

Strona 61 - OPERATION

264975-BIM-B-120864 Johnson Controls Unitary ProductsFLASH CODESThe UCB will initiate a flash code associated with errorswithin the system. Refer to U

Strona 62 - SAFETY CONTROLS

264975-BIM-B-1208Johnson Controls Unitary Products 65TEMPERATURE LIMITIf the UCB senses zero volts from the high temperature limit,the indoor blower m

Strona 63 - 50” CABINET

264975-BIM-B-120866 Johnson Controls Unitary ProductsThe ICB monitors the Pressure and Rollout switches of gasheat units.The control circuit includes

Strona 64

264975-BIM-B-1208Johnson Controls Unitary Products 67POST START CHECK LIST1. Verify proper system pressures for both circuits.2. Measure the temperatu

Strona 65

264975-BIM-B-120868 Johnson Controls Unitary Productsvalve) clockwise to increase manifold pressure or counterclockwise to decrease manifold pressure.

Strona 66 - START-UP (COOLING)

264975-BIM-B-1208Johnson Controls Unitary Products 69EXAMPLE:By actual measurement, it takes 19 seconds for the hand ona 1 cubic foot dial to make a r

Strona 67 - START-UP (GAS HEAT)

264975-BIM-B-1208Johnson Controls Unitary Products 7NOMENCLATURED U -10 N18 A T A AA 3 0 1 2 4 AD = A/C, Single Pkg., R-22Product CategoryA = Std. Mot

Strona 68 - TABLE 69: GAS HEAT STAGES

264975-BIM-B-120870 Johnson Controls Unitary ProductsCHARGING THE UNITThese units should be charged using the superheat method.Super heat charging dat

Strona 69

264975-BIM-B-1208Johnson Controls Unitary Products 71TABLE 73: DL-08 (8.5 TON) STANDARD EFFICIENCY SUPERHEAT CHARGINGOutdoorTemp (°F)Superheat at Comp

Strona 70 - CHARGING THE UNIT

264975-BIM-B-120872 Johnson Controls Unitary ProductsTABLE 75: DL-12 (12.5 TON) STANDARD EFFICIENCY SUPERHEAT CHARGINGOutdoorTemp (°F)Superheat at Com

Strona 71

264975-BIM-B-1208Johnson Controls Unitary Products 73DU-10 (10 ton) high efficiency unit uses TXV. Charge the unit to 10° subcooling.TABLE 77: DU-07 (

Strona 72

264975-BIM-B-120874 Johnson Controls Unitary ProductsTROUBLESHOOTING DL/DU FLASH CODESVarious flash codes are utilized by the unit control board (UCB)

Strona 73

264975-BIM-B-1208Johnson Controls Unitary Products 75FIGURE 30 - UNIT CONTROL BOARDUNIT CONTROL BOARD OPTION SETUPOPTION BYTE SETUP• Enter the Option

Strona 74 - TROUBLESHOOTING

264975-BIM-B-120876 Johnson Controls Unitary ProductsTABLE 81: HEAT DELAYHeatFan OnDelayHeat Fan OffDelayRedLED 8RedLED 4RedLED 2RedLED 160 180 On On

Strona 75 - HEAT DELAY SETUP

264975-BIM-B-1208Johnson Controls Unitary Products 77FIGURE 31 - BASIC TROUBLESHOOTING FLOWCHARTMonitorMonitoredSystemsProblem?Call forCooling?Call

Strona 76 - TABLE 81: HEAT DELAY

264975-BIM-B-120878 Johnson Controls Unitary Products FIGURE 33 - TRIP FAILURE FLOW CHARTT r i p / F a i l u r eL o s s o fL S I n p u tE n e r g

Strona 77 - Power to

264975-BIM-B-1208Johnson Controls Unitary Products 79COOLING TROUBLESHOOTING GUIDEOn calls for cooling, if the compressors are operating but thesupply

Strona 78

264975-BIM-B-12088 Johnson Controls Unitary ProductsINSTALLATIONINSTALLATION SAFETY INFORMATIONRead these instructions before continuing this applianc

Strona 79 - COOLING TROUBLESHOOTING GUIDE

264975-BIM-B-120880 Johnson Controls Unitary Productslocked out the compressor for repeat trips. The UCB should be flashing an alarm code. If not, pre

Strona 80

264975-BIM-B-1208Johnson Controls Unitary Products 818. If 24 volts is present at the UCB Y2 terminal, the com-pressor may be out due to an open high-

Strona 81

264975-BIM-B-120882 Johnson Controls Unitary Products11. If 24 volts is present at the UCB Y1 terminal and the compressor is not out due to a protecti

Strona 82

264975-BIM-B-1208Johnson Controls Unitary Products 839. If the blower motor runs with the fan switch in the “ON” position but does not run shortly aft

Strona 83

Subject to change without notice. Printed in U.S.A. 264975-BIM-B-1208Copyright © 2009 by Johnson Controls, Inc. All rights reserved. Supersedes: 26497

Strona 84 - Norman, OK 73069

264975-BIM-B-1208Johnson Controls Unitary Products 9 LIMITATIONSThese units must be installed in accordance with the follow-ing:In U.S.A.:1. National

Komentarze do niniejszej Instrukcji

Brak uwag